Winkelwagen

<< Vorige - Volgende >>


RME AEB4-I


24 Bit / 48 kHz, 4 Analog Balanced Inputs for DIGI96 & HDSP PCI Cards

Artikelcode: Std-Ra-Rm-23



RME AEB4-I




The AEB4-I (Analog Expansion Board) adds 4 analog inputs in professional quality to all ADAT capable RME cards (see below). Level adjustment +4 dBu/-10 dBV, 107 dBA SNR and a servo balanced input circuit deliver perfect sound and sonic clarity.

The AEB4-I is designed for maximum flexibility. Both stereo inputs 1/2 3/4 are automatically copied to channels 5/6 and 7/8. Installation is done in a convenient manner using the supplied bracket, or - as no contact to any slot on the motherboard is needed - at any place inside the computer. Nuts for all TRS jacks and a drilling template are included.

 OPERATING THE AEB4/8-I
 
 

Using the Analog Expansion Board is very easy to do, thanks to the clearly structured and informative Settings dialog of the RME cards. The AEB4/8-I operates like any other converter with ADAT output, but is connected internally. Therefore the card's input selector has to be set to 'Internal'.

The AEB gets its clock from the DIGI (thus works as slave.) To avoid a clock loop the card has to be switched into 'Master' mode (field 'Clock Mode'.)

The Input Status display now shows the selected input (Internal), the current sample rate (44.1/48) and format (Adat.)

 
 
 TECHNICAL SPECIFICATIONS AND FEATURES 

  
Input AEB4-I 4 x 1/4" TRS jack, servo balanced 
Input AEB8-I 4 x 1/4" TRS jack, unbalanced 
Dynamic ratio 104 dB (RMS unweighted), 107 dBA 
THD+N -95 dB (0.0017 %) 
Frequency response -0.1 dB: 10 Hz - 21 kHz 
Input level for 0 dBFS @ +4 dBu: +12 dBu 
Input level for 0 dBFS @ -10 dBV: +2 dBV 
Crosstalk > 110 dB 
Supported sample rates 32 kHz - 48 kHz 
Input impedance 10 kOhm 
Power supply uses 3.5" floppy connector, 12 V/5 V DC, 190 mA 
AEB needs no slot on the motherboard 
Standard bracket, board dimensions AEB4: 85 x 95 mm, AEB8: 120 x 95 mm 
1 internal cable 2-pin, 1 internal cable 3-pin, 1 power adapter cable 5 1/4" to 2 x 3.5" included 

 
COMPATIBILITY NOTES
 
 

HDSP 9652 
Two AEBx-I and two AEBx-O or two TEB can be connected and operated simultaneously, in all possible combinations. One TEB can be used together with either one AEBx-I or AEBx-O.
 

DIGI96 SERIES 

AEBs use the internal ADAT interface of the DIGI cards. Therefore they do not work with the DIGI96 (which did not support ADAT.) To operate the AEB4-I and AEB8-I the used DIGIs must have the connectors ST6/7 on board (for the Word Clock Module.) These were not present on the very first cards of the DIGI96 series (1998 to beginning of 1999.)

One AEBx-I and one AEBx-O can be connected and operated simultaneously, in all possible combinations. Or one TEB.
  

HAMMERFALL DSP MULTIFACE / DIGIFACE 

Multiface and Digiface use the Hammerfall DSP PCI card. This card has no internal inputs or outputs. Therefore no Expansion Boards can be used.
  

HAMMERFALL SERIES 

An operation with the Hammerfall or Hammerfall Light requires board revision 1.5 or higher, because the internal connectors ADAT1Out, ADAT2Out and ST7 were not implemented in earlier versions.

One AEBx-I and two AEBx-O can be connected and operated simultaneously, in all possible combinations. Or one TEB and one AEBx-O.




euro 164.10





Aantal