<< Vorige - Volgende >>


36 Channel 24 Bit/96 kHz I/O Box

Artikelcode: Std-Ra-Rm-05


8 x analog line I/O, 96 kHz/24 bit, SNR 111 dBA, 1/4" TRS jacks 
1 x ADAT digital I/O 
1 x SPDIF digital I/O 
1 x Word clock I/O (BNC) 
1 x hi-power analog line/headphone output, separate output for independent submix 
1 x MIDI I/O, 16 channels high-speed MIDI 
Hardware level calculation: freely scalable level meters, peak and RMS calculation without CPU load 
TotalMix: 720 channel mixer with 40 bit internal resolution. MIDI remote controllable. 
S/MUX poured in hardware: 4 channels 96 kHz/24 bit for record and playback via ADAT optical 
...and numerous other features found already in the Hammerfall series. And all this for an unbeatable price! 

The Hammerfall® DSP System comes with drivers for Windows 98/ME (MME with multi-client operation, ASIO 2.0, GSIF), Windows 2000/XP (fully multi-client operation of MME, GSIF and ASIO 2.0 plus ASIO multi-client), Mac OS 9.x (ASIO 2.0, OMS MIDI) and Mac OS X (Core Audio, Core MIDI). 

The front panel hosts some useful status LEDs, like MIDI state, lock state of the digital inputs and error state of the host-bus. Additionally there's a high-quality 24 bit/96 kHz analog line output, also usable with headphones, and one MIDI I/O. 


The rear of the Multiface II shows unrivalled connectivity: 8 analog line I/Os on 1/4" TRS jacks (balanced, 24 bit/96 kHz), ADAT optical I/O (switchable to SPDIF optical), SPDIF I/O coaxial, word clock I/O and MIDI I/O. Don't settle for less! 

The Multiface II can be used with laptops as well as desktop computers. The connection to notebooks is achieved via a CardBus card, the connection to desktops via a PCI card. These interfaces are sold separately.

Supported sample rates: 32 kHz, 44.1 kHz, 48 kHz, 64 kHz, 88.2 kHz, 96 kHz, variable 
8 buffer sizes/latencies available: 1.5 ms, 3 ms, 6 ms, 12 ms, 23 ms, 46 ms, 93 ms, 186 ms 
ASIO zero CPU load technology: 0 (zero!)% CPU load when using ALL 36 channels! 
All settings changeable in realtime 
Clock modes slave and master 
Automatic, intelligent master/slave clock control 
Enhanced Mixed mode: All inputs and outputs simultaneously operational 
Unsurpassed Bitclock PLL (audio synchronization) in ADAT mode 
Enhanced Zero Latency Monitoring for latency-free submixes and perfect ASIO Direct Monitoring 
Comes with DIGICheck: the ultimate measurement, analysis and test tool 
Dynamic ratio analog AD: 111.5 dBA, DA: 112 dBA 
THD+N AD: -98 dB (0.0012%), DA: -97 dB (0.0014%) 
Analog level @ 0 dBFS (set by front panel switch): +2 dBV, +13 dBu, +19 dBu 
Dynamic ratio stereo monitor output: 119 dBA, output impedance 30 Ohm 
Input 8 x line (1/4" TRS jacks), 1 x optical (TOSLINK), 1 x coaxial (Cinch), 1 x MIDI, word clock (BNC) 
Input format SPDIF, AES/EBU (Consumer, Professional), ADAT optical  
8 x line (1/4" TRS jacks), 1 x optical (TOSLINK), stereo analog line (TRS), 1 x coaxial (phono), 1 x MIDI, word clock (BNC) 
Format output SPDIF, AES/EBU (Consumer/Professional), ADAT optical 


Intelligent clock control according to operational mode and present/desired sample rate.
Bitclock PLL
The most reliable receiver circuit for ADAT optical signal.
Enhanced ZLM®
Monitoring of the input signal, independent from clock mode and sample rate.
Professional status and level display at lowest CPU load.
Intelligent Clock Control
Measurement and display of all incoming and used clocks.
Latency Fast Change
Change latency on-the-fly under ASIO, without manual reset or re-boot.
Surveillance and sample accurate synchronization of all channels.
Comparison and display of all input's clock status.
Mixes all inputs and all outputs on all outputs. Several independent submixes possible.
Zero Latency Monitoring - ZLM®
Automatic monitoring of the input signal with zero latency.

euro 749.00